METAL ROOF SYSTEMS

We install metal roofs and recommended different metal roof solutions depending on your unique needs. We use products from manufacturers Bruce and Dana and Taylor Metal, among others. We offer all metal roof products. However, the most common metal roof we install uses a snap and lock panel system.

Metal roofs are durable, fire retardant and low maintenance. They are energy efficient as metal reflects heat and blocks its transfer into the house. Steel roofs offer other environmental benefits as well. They are made from up to 70 percent recyclable material and since they weigh so little they can be installed over existing roofs, eliminating the need to dispose of the original roof.

The initial cost of a premium metal roof can be higher than other roofing materials, but if you calculate the lifecycle cost, a metal roof can prove to be a better investment than some other types of roofing.

Snap Lock Standing Seam Metal System by Bruce and Dana

This unique design concept of Snap Lock Standing Seam was introduced to the Northwest by Bruce & Dana, Inc. in 1983. Snap Lock features a concealed fastening system, anti-siphoning gaps and precise rib snapping action to provide what we believe to be the most watertight panel around. Available in 13 premium PVDF paint colors at .020 C galvanized. 35 year non-prorated warranty.

Very low maintenance. Minimum 50 year roof. Class A fire rating. Energy savings. Yearly savings on homeowners insurance. 90mph wind uplift rating. Roofing is 100% recyclable.

Our products are American made, American owned materials. BRUCE & DANA, INC., SNAP LOCK STANDING SEAM is one of the very few panels that qualify under the BUY AMERICAN act of the Federal government.

Snap Lock Standing Seam have a premium 35 year PVDF paint system and are available in 13 colors. Actual colors may vary. Contact us to make your final color selection.

Easy Lock™ Standing Seam System by Taylor Metal

The ultimate in a Standing Seam pattern. Easy Lock™ is appreciated for both its beauty and function. The panels provide one foot wide coverage with concealed fastening screws and a 1-1/8" high snap-together lock seam, and lengths up to 50 feet. This system allows application down to 1/2" in 1 foot pitch with fasteners being applied to the pre-slotted flange along one side of the panel. The next panel easily snaps and locks over the flange area, completely concealing the flathead screws, and provides a secure roof in winds up to 140 mph.

Most metal roofing uses exposed fasteners with a neoprene seal. However, expansion/contraction ovoids the fastener holes and sunlight shrinks the washer. Hence, exposed fastener roofing will eventually leak. The roofing panels designed by Taylor Metal Products have concealed fasteners which are not exposed and cannot leak - ever. The fasteners are applied through a pre-slotted flange on the side of the panel. The next panel easily snaps and locks over the flange area, completely concealing the screws, and providing a secure roof in winds up to 140 mph. No clips, special closures, or mechanical seaming are used. Where "dry" is important, a concealed fastener is a must!

The exclusive Easy-Lock™ system incorporates an air space on the snap leg side between inner and outer ribs. This prevents water siphoning by wind pressure and capillary action. The resulting ventilated dry seam eliminates joint corrosion and fastener rust out. This roofing system allows application down to 1/2 inch in 1 foot pitch, and over most existing roofing without tear off. Installation can also be on plywood, stripping, or trusses with purlins.

Low Maintenance. No Moss. No Fire Danger. No Snow, Leaf, or Needle Build-up. No Cracking or Curling. 50 - 60 Year Life on Painted Panels.

Taylor Metal Products offers several colors and finishes for your project. Finishes are applied as per ASTM A-653. Also available - 16 and 20 ounce Copper, acrylic Galvalume, and custom color finishes.

24 Gauge

NOTE: The colors shown may differ in varying degrees from the actual metal colors.

26 Gauge